Step 13. Read the resin instructions for safety concerns regarding the Nunn Design Resin. Printed instructions on how to mix the resin TIP: It is always a good idea to remove excess ink from your rubber stamp prior to storing them.Ģ precision tips to screw onto the bottles If you aren’t able to wipe away the ink, pinch off the stamped surface and add some additional clay to bring up your surface to be even with the side edge of your bezel and stamp again until you have it just the way you like it. Step 12. If you don’t like how your image looks stamped on the Epoxy Clay, you can use a wet-wipe to remove the ink. Press down gently into the clay, creating a stamped image. Once you are all inked up, place your rubber stamp upright over your epoxy clay filled bezel. I like to test my impression by stamping onto a sheet of white paper prior to actually stamping on the Epoxy Clay. Step 11. Ensure that your ink pad is nicely inked so that you have an even coverage on your rubber stamp. Step 10. Wipe any excess clay from the bezel using a wet-wipe. Press the clay into the bezels, using a toothpick for the hard to insert corners. Step 9. Roll a ball of Epoxy Clay in the palm of your hand until it is smooth without any creases. Step 8. Clean and apply a piece of packing tape onto the backside of the Nunn Design Open Back Bezels. The Epoxy Clay hardens like cement, so cleaning it up now and being tidy as you go makes the process easier and the results so much nicer. Step 7. Use a wet-wipe to clean-up any excess Epoxy Clay that might have been left on the jewelry finding. Tip: Be sure to check the backside to make sure you are getting the Epoxy Clay into all of the crevices and corners of the bezel. Pat the toothpick marked clay with your fingers until smooth. If filling the corners with Epoxy Clay is challenging, use a toothpick to press the clay up into the corners of the bezel. If you have too much clay, you can pinch off the excess and pat down until smooth again, or remove it from the bezel altogether and remove the excess. For this particular technique, I wanted the Epoxy Clay to be flush to and level with the sides of the bezel. Step 6. Press the ball of mixed Epoxy Clay into your bezel using the tips of your fingers. Step 5. Roll the thoroughly mixed Epoxy Clay between your palms until it forms a smooth round ball. Use a wet-wipe to also clean your hands of any baby powder prior to handling the clay. Store the gloves for your next creative jewelry making project. Prior to removing the gloves, use a wet-wipe to clean them fully. Step 4. Once the clay is mixed, you can safely handle the clay without wearing gloves. Store Part A and Part B in separate zip-lock bags to avoid contamination while it is in storage. Tip: Make sure to wrap up your Epoxy Clay to prevent it from drying out and hardening. I would recommend having plenty of bezels prepped just in case you have excess clay. Tip: I guesstimate the amount of Epoxy Clay that I will need to fill the bezels for the project I’m working on. Blend together the 2 parts fully until the clay is no longer marbled and is uniform in color. Step 3. With the gloves on, open up the packages of Epoxy Clay and pinch off two equal-sized balls of Part A and Part B. This will make it easier to get the gloves off once you are finished mixing the Epoxy Clay. To get the most usage out of the gloves, place baby powder generously over your hands prior to putting the gloves on. I use my latex gloves over and over again to prevent waste. If you do not have a latex allergy, I recommend using a pair of industrial, powder-free, 5 mils, latex glove sized to fit your hand snugly. If you are having the same challenge try a different brand. They are way too big for my hands and I have a heck of time mixing and colorizing the clay while wearing them. The gloves that are included in the Epoxy Clay Kits are not my favorite. Once the clay is mixed it is activated and is neutral and gloves are no longer necessary. Prior to mixing the 2 parts, it is recommended by the manufacturer to wear gloves when handling. Once the clay is activated you have 90-120 minutes before the clay hardens and you can no longer sculpt or embed objects. Mixing equal parts of A & B activates the clay. To clean, get the tip of a Q-Tip wet with rubbing alcohol and clean away any of the blackened oxidization on all the surfaces of the bezel. To avoid this, clean the bezel thoroughly prior placing the Epoxy Clay within the finding. The oxidization, when it comes into contact with the mixed Epoxy Clay could change the color of the clay. Step 1. The Nunn Design Findings are oxidized to provide the aged look to the precious metal plating.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |